Программа Сервисный Центр
Сортировать новости по: дате новости | популярности | посещаемости | комментариям | алфавиту
0

Amiga Mouse/Joy

  • 26-11-2009, 13:32
  • Просмотров: 1709
Amiga Mouse/Joy

9 PIN D-SUB MALE (at the computer)
9 PIN D-SUB FEMALE (at the mouse/joy cable)

9 PIN D-SUB MALE at the computer.
9 PIN D-SUB FEMALE at the mouse/joy cable.

Pin Mouse/Trackball Lightpen Digital Joystick Paddle Dir Comment
1 V-pulse /FORWARD BUTTON 3 <--  
2 H-pulse /BACK <--  
3 VQ-pulse /LEFT BUTTON 1 <--  
4 HQ-pulse /RIGHT BUTTON 2 <--  
5 BUTTON 3(M) Penpress PotX <->  
6 BUTTON 1(L) /Beamtrigger /BUTTON 1 <->  
7 +5V +5V +5V +5V --> 50 mA max
8 GND GND GND GND ---  
9 BUTTON 2(R) BUTTON 2 BUTTON 2 PotY <->  

Note: Direction is Computer relative Device.
Note: Pot is a linear 470 kOhm (±10 %)

 
Amiga External Diskdrive

23 PIN D-SUB FEMALE (at the Amiga)

23 PIN D-SUB FEMALE at the Amiga.

Pin Name Dir Description
1 /RDY <-> Disk Ready
2 /DKRD <-- Disk Read Data
3 GND --- Ground
4 GND --- Ground
5 GND --- Ground
6 GND --- Ground
7 GND --- Ground
8 /MTRXD OC Disk Motor Control
9 /SEL2 OC Select Drive 2
10 /DRES OC Disk Reset
11 /CHNG <-> Disk Removed From Drive-Latched Low
12 +5V --> +5 Volts DC (250 mA max)
13 /SIDE --> Select Disk Side (0=Upper, 1=Lower)
14 /WPRO <-> Disk is Write Protected
15 /TKO <-> Drive Head position over Track 0
16 /DKWE OC Disk Write Enable
17 /DKWD OC Disk Write Data
18 /STEP OC Step the Head-Pulse, First low, then high
19 DIR OC Select Head Direction (0=Inner, 1=Outer)
20 /SEL3 OC Select Drive 3
21 /SEL1 OC Select Drive 1
22 /INDEX OC Disk Index Pulse
23 +12V --> +12 Volts DC (160 mA max, 540 mA surge

Note: Direction is Computer relative Diskdrive.

 
Amiga 500/600/1200 Power Supply

UNKNOWN (at the motherboard)

UNKNOWN CONNECTOR at the motherboard.

Pin Name
1 +5V
2 Shield Ground
3 +12V
4 Signal Ground
5 -12V
 
Amiga 2000 Power Supply

UNKNOWN (at the motherboard)

UNKNOWN CONNECTOR at the motherboard.

Pin Name
1 +5V
2 +5V
3 +5V
4 +5V
5 GND1
6 GND2
7 GND3
8 GND4
9 +12V
10 KEY
11 -12V
12 +5V USER
13 -5V
14 TICK

You will be able to tell the orientation with the help of pin 10, it is missing.

Note: TICK is NOT found on PC power supplies

 
Amiga 3000 Power Supply

UNKNOWN (at the motherboard)

UNKNOWN CONNECTOR at the motherboard.

Pin Name
1 +VID
2 +5V
3 +5V
4 +5V
6 GND
7 GND
8 GND
9 GND
10 GND
11 -5V
12 +5V USER
13 TICK
14 -12V/-12V USER
15 +12V/+12V USER
 
Amiga 3000T Power Supply

UNKNOWN (at the motherboard)

UNKNOWN CONNECTOR at the motherboard.

Pin Name
1 TICK
2 -12V
3 -5V
4 GND
5 GND
6 GND
7 GND
8 GND
9 +5V
10 +5V
11 +5V
12 +5V
13 FAIL
14 +12V
15 +12V
16 +5V USER
17 GND
18 GND
19 GND
20 GND
21 +5V
22 +5V
23 +5V
24 +5V
 
Amiga Video Expansion

36+54 PIN EDGE CONNECTOR (at the computer)

36+54 PIN EDGE CONNECTOR at the computer.

Pin Name Dir Description
1 RGB16 --> Red Bit 0
2 RGB17 --> Red Bit 1
3 LINELF --> Audio Line Out Left
4 LINERT --> Audio Line Out Right
5 C28D --> Pixel-Synchronous Clock
6 +5V - +5 Volts DC (1 A)
7 ARED --> Analog Red
8 +5V - +5 Volts DC (1 A)
9 GND - Digital Ground
10 +12V - +12 Volts DC (40 mA)
11 AGREEN --> Analog Green
12 GND - Digital Ground
13 GND - Digital Ground
14 /CSYNC --> Composite Sync
15 ABLUE --> Analog Blue
16 /XCLKEN <-- Genlock Clock Enable
17 GND - Digital Ground
18 BURST --> Burst Gate
19 /C4 --> 3.55/3.58 MHz Clock
20 GND - Digital Ground
21 GND - Digital Ground
22 /HSYNC --> Horizontal Sync (47 Ohm)
23 RGB4 --> Blue Bit 4
24 GND - Digital Ground
25 RGB7 --> Blue Bit 7
26 /VSYNC --> Vertical Sync (47 Ohm)
27 RGB15 --> Green Bit 7
28 BLANK --> Video Blank
29 RGB23 --> Red 7
30 /PIXELSW --> Genlock Overlay (47 Ohm)
31 -5V - -5 Volts DC
32 GND - Digital Ground
33 /XCLK <-- Genlock Clock
34 /C1 --> C1 Clock
35 +5V - +5 Volts DC (1 A)
36 PSTROBE --> Printer Port Handshake
       
1 GND - Digital Ground
2 RGB20 --> Red Bit 4
3 RGB21 --> Red Bit 5
4 RGB22 --> Red Bit 6
5 GND - Digital Ground
6 RGB12 --> Green Bit 4
7 RGB13 --> Green Bit 5
8 RGB14 --> Green Bit 6
9 GND - Digital Ground
10 RGB5 --> Blue Bit 5
11 RGB6 --> Blue Bit 6
12 GND - Ground
13 SOG --> Sync-On-Green Indicator
14 TBASE --> 50/60 Hz Software Clock Timebase
15 CDAC --> 7.09/7.16 MHz Clock
16 PPOUT <-> Printer Port Paper Out
17 /C3 --> 3.55/3.58 MHz Clock
18 PBUSY <-> Printer Port Busy
19 /LPEN <-- Light Pen Input
20 /PACK <-> Printer Port Acknowledge Handshake
21 PSEL --> Printer Port Select
22 GND - Digital Ground
23 PPD0 <-> Printer Port Data Bit 0
24 PPD1 <-> Printer Port Data Bit 1
25 PPD2 <-> Printer Port Data Bit 2
26 PPD3 <-> Printer Port Data Bit 3
27 PPD4 <-> Printer Port Data Bit 4
28 PPD5 <-> Printer Port Data Bit 5
29 PPD6 <-> Printer Port Data Bit 6
30 PPD7 <-> Printer Port Data Bit 7
31 /LED --> LED (Audio filter bypass) Setting
32 GND - Digital Ground
33 RAWLF --> Raw (Unfiltered) Audio Left
34 AGND - Audio Ground
35 RAWRT --> Raw (Unfiltered) Audio Right
36 AGND - Audio Ground
37 - Reserved for future expansion
38 - Reserved for future expansion
39 GND - Digital Ground
40 GND - Digital Ground
41 - Reserved for future expansion
42 - Reserved for future expansion
43 GND - Digital Ground
44 GND - Digital Ground
45 RGB18 --> Red Bit 2
46 RGB19 --> Red Bit 3
47 RGB8 --> Green Bit 0
48 RGB9 --> Green Bit 1
49 RGB10 --> Green Bit 2
50 RGB11 --> Green Bit 3
51 RGB0 --> Blue Bit 0
52 RGB1 --> Blue Bit 1
53 RGB2 --> Blue Bit 2
54 RGB3 --> Blue Bit 3

Note: Direction is Motherboard relative Card.
Note: Do not mix analog & digital grounds.

 
Amiga 1000 RF Modulator

UNKNOWN (at the motherboard)

UNKNOWN CONNECTOR at the motherboard.

Pin Name
1 N.C.
2 GND
3 AUDIO LEFT
4 COMP VIDEO
5 GND
6 N.C.
7 +12V
8 AUDIO RIGHT
 
0

Amiga Video

  • 26-11-2009, 13:31
  • Просмотров: 2027
Amiga Video

23 PIN D-SUB MALE (at the Amiga)

23 PIN D-SUB MALE at the Amiga.

Pin Name Dir Description
1 /XCLK <-- Extern Clock
2 /XCLKEN <-- Extern Clock Enable (47 Ohm)
3 RED --> Analog Red (75 Ohm)
4 GREEN --> Analog Green (75 Ohm)
5 BLUE --> Analog Blue (75 Ohm)
6 DI --> Digital Intensity (47 Ohm)
7 DR --> Digital Red (47 Ohm)
8 DG --> Digital Green (47 Ohm)
9 DB --> Digital Blue (47 Ohm)
10 /CSYNC --> Composite Sync (47 Ohm)
11 /HSYNC --> Horizontal Sync (47 Ohm)
12 /VSYNC --> Vertical Sync (47 Ohm)
13 GNDRTN --- Digital Ground (for /XCLKEN) Don"t connect with pin 16-20.
14 /PIXELSW --> Genlock overlay (47 Ohm)
15 /C1 --> Clock out (47 Ohm)
16 GND --- Video Ground
17 GND --- Video Ground
18 GND --- Video Ground
19 GND --- Video Ground
20 GND --- Video Ground
21 -12V --> -12 Volts DC (10 mA max) (A500/A600/A1200)
  -5V --> -5 Volts DC (10 mA max) (A1000/A2000/A3000/A4000)
22 +12V --> +12 Volts DC (100 mA max)
23 +5V --> +5 Volts DC (100 mA max)

Note: Direction is Computer relative Monitor.

 
Amiga 1000 RF Monitor

8 PIN DIN "C" FEMALE (at the computer)

8 PIN DIN "C" FEMALE at the computer.

Pin Name Dir Description
1 - Not connected
2 GND --- Ground
3 AUDL --> Audio Left
4 CVIDEO --> Composite Video
5 GND --- Ground
6 - Not connected
7 +12V --> +12 VDC
8 AUDR --> Audio Right

Note: Direction is Computer relative Monitor.

 
 

 
 
 
Обратная связь

Наши партнеры

 

Опросы

Есть ли справедливость в жизни?
Конечно есть, уверен!
Вроде как должна быть, но...
Затрудняюсь ответить...
Какая справедливость? О чем Вы?
Эх.., нет правды на свете!

 

Облако тегов

Требуется для просмотраFlash Player 9 или выше.

Показать все теги
 

Календарь публикаций

«    Ноябрь 2017    »
ПнВтСрЧтПтСбВс
 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
 
 

Архив новостей

Сентябрь 2017 (4)
Август 2017 (36)
Июль 2017 (32)
Июнь 2017 (42)
Май 2017 (45)
Апрель 2017 (47)
 
Наверх Сервисные мануалы Даташиты Ремонт LCD, ЖК телевизоров LG Samsung Скрипт программы "Сервисный центр"